Translate German to English - Click here to open Altavista's Babel Fish Translator Click here to learn about all those symbols by people's names.

leftlogo.jpg (20709 bytes)

Upgrade to Premium Membership

Previous Thread
Next Thread
Print Thread
Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
Hi All

I have this M33 dagger and noticed that the blade/scabbard fitting is not optimal. You can see a 2 mm space between the cross guard and the blade itself. Is this something to be worried off ?

Also, what is the opinion about the eagle. Seems to be a long neck version ??, but is not perfectly set in the wood.


I would appreciate your opinion. Thanks

small_Afbeelding_014.jpg (72.45 KB, 316 downloads)
Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
next picture

small_Afbeelding_016.jpg (39.96 KB, 316 downloads)
Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
and again

small_Afbeelding_017.jpg (57.12 KB, 306 downloads)
Joined: Jan 2003
Posts: 1,539
Offline
Joined: Jan 2003
Posts: 1,539
Hi Ben,

I dunno, we'll need to see some close ups.

Just kidding! Razz

I don't see the small gaps between the grip and the crossguard as hard evidence (from these photos) that this dagger is assembled from parts or is a bad dagger. I take it from the plating that this is a later dagger (an RZM) which historically had lesser quality controls than the early 33 SS EM daggers. Tom Wittmann writes about this and addresses it in his chapter of Johnson's book regarding SS daggers.

Moreover, wood shrinks over time and with changes in temperature and humidity. The eagle is not perfectly set in the wood as you mention, but again, Wittmann shows a photo of an RZM dagger where the grip eagle on an RZM is actually about 3 mm off from the center bridge of the grip. These things were not installed during the 1930's with laser controlled lathes either.

The gap between the crossguard and the blade could raise some red flags. Even on later daggers, it should not be too pronounced. Do you have a picture of it?

Last question - it that a leather washer on the end of the blade? There should not be one.


<img src="http://img.villagephotos.com/p/2002-4/20265/XBQKF-me109-transparent.gif" width=115 height=34>
Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
quote:
Börse

Hello Börse

many thanks for your reply. The gap I mentinned is between the crossguard and the scabberd. I added a new picture.

There is a perfect fit between the blade and the crossguard (see picture)

Thanks!
Ben

small_m33_2006-01-29_005.JPG (54.33 KB, 272 downloads)
Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
blade - crossguard fit

smalm_m33_2006-01-29_004.JPG (39.57 KB, 271 downloads)
Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
Its indeed an RZM dagger

Joined: Sep 2000
Posts: 15,084
Likes: 96
Online Content
Joined: Sep 2000
Posts: 15,084
Likes: 96
Ben,

That slight gap seems to be even from left to right. Is is just that the dagger will not fully seat in the scabbard ?

Dave

Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
Dave
yes, the dagger does not fully seat in the scabberd

Ben

Joined: Oct 2001
Posts: 3,037
Likes: 4
Offline
Joined: Oct 2001
Posts: 3,037
Likes: 4
Gailen told me that SS daggers were sometimes found with leather washers for exactly this reason. The washer filled the space between the crossguard and the scabbard when the fit wasn't so German perfect. Most washers have been removed because they are not "textbook". The only known example of a Louper has a leather washer as can be seen on page 29 of Wittmann's volume.

Joined: Aug 2001
Posts: 3,958
Likes: 29
S
Offline
S
Joined: Aug 2001
Posts: 3,958
Likes: 29
Hi either the lead weight in the bottom of the scabbard is dislodged and preventing the blade from entering fully or the scabbard did not originally belong to the piece. That is a fairly substantial gap even for a late period plated RZM dagger.cheers, Ryan

Joined: Jul 2001
Posts: 3,806
S
sdp Offline
Offline
S
Joined: Jul 2001
Posts: 3,806
I'm having the same thoughts as Ryan above.

Joined: Sep 2000
Posts: 15,084
Likes: 96
Online Content
Joined: Sep 2000
Posts: 15,084
Likes: 96
I asked the question thinking of the scabbard weight ... if there is one present.

The scabard weights are variously shaped pieces of lead that are held in the bottom of the scabbard by the screws that also secure the lower scabbard fitting. At a point after RZM dagger production began, the weights we eliminated. You can usually tell just by hefting the scabbard. Sometimes they get loose and jam the blade.

The other possibility is that the scabbard has been switched and the throat is not wide enough because it was not filed during fitting. You should be able to see if it is catching.

Dave

A
Anonymous
Unregistered
Anonymous
Unregistered
A
Sometimes it's just a replaced screw in the scabbard upper fitting being too long or not notched that prevents the blade from going in.

Mark Wink

Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
I went into the scabbard with a long needle to measure its length and I noticed is is a bit too short to hold the blade. Just a few mm. I do not know if a scabbard weight is present. If it is, could this problem be fixed by removing the lower scabbard fitting?

Ben

A
Anonymous
Unregistered
Anonymous
Unregistered
A
If there is a lead weight in there, the only way to get it out or move it into correct position is to simply remove or loosen the screws on the lower scabbard fitting and then try to move the weight with the long needle or some long thin screwdriver. If you don't have to totally remove the screws, don't. They can be a real booger to re-install without messing up the threads. All you may have to do is loosen them to get them to release the weight assuming its there. I use a light on the end of a long rod to look into my scabbards. You can often find them at gunshows as "bore lights". Saved me a great amount of guessing on whats in there way down a scabbard.

Mark Cool

Joined: Sep 2004
Posts: 66
B
Ben38 Offline OP
OP Offline
B
Joined: Sep 2004
Posts: 66
Mark

Thanks for the tip. I did exactly what you said, and this is the result. I guess its acceptable now for an RZM dagger ?
What do you think ?
Ben

smal_2006-01-30_003.JPG (13.54 KB, 108 downloads)
Joined: Aug 2001
Posts: 3,958
Likes: 29
S
Offline
S
Joined: Aug 2001
Posts: 3,958
Likes: 29
Hi it looks a lot better. cheers, Ryan

Joined: Sep 2000
Posts: 15,084
Likes: 96
Online Content
Joined: Sep 2000
Posts: 15,084
Likes: 96
This old topic looks at RZM dagger fit to scabbard.

Dave


Moderated by  Dave 

Link Copied to Clipboard
Popular Topics(Views)
2,261,526 SS Bayonets
1,760,292 Teno Insignia Set
1,128,769 westwall rings
Latest New Threads
Luftwaffe Swords
by Tanker - 03/27/2024 07:29 PM
Paul Weyersberg Heer
by Tanker - 03/27/2024 07:13 PM
HJ Fahrtenmesser,
by OWN - 03/27/2024 07:05 PM
Wir fahren gegen Engelland - Battle of Britain
by Stephen - 03/27/2024 10:06 AM
Hiddensee brooch
by benten - 03/24/2024 04:13 PM
Latest New Posts
F Dula with a twist
by C. Wetzel-20609 - 03/28/2024 09:29 PM
Personalized reproduction honor ring source?
by Simone - 03/28/2024 08:57 PM
HJ Fahrtenmesser,
by OWN - 03/28/2024 06:18 PM
Wir fahren gegen Engelland - Battle of Britain
by Gaspare - 03/28/2024 12:34 AM
Paul Weyersberg Heer
by Tanker - 03/27/2024 11:30 PM
Forum Statistics
Forums42
Topics31,652
Posts328,708
Members7,501
Most Online5,900
Dec 19th, 2019
Who's Online Now
12 members (Dave, C. Wetzel-20609, Vern, The_Collector, Documentalist, Honestmike, Baz69, Simone, Nietzsche, Stephen, JonathanC, Tanker), 394 guests, and 115 robots.
Key: Admin, Global Mod, Mod

Powered by UBB.threads™ PHP Forum Software 7.7.5