|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
Normally the owner of the ring wants a place on the ring , where he has been . Osten/ East 1941 is very globally : for example Polen, Ukrain, Russia . Maybe he has been on many places ......or he didn't want to remeber where he has been exactly ? :)
Last edited by benten; 01/24/2021 04:49 PM.
|
|
|
|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
|
|
|
|
Joined: Jun 2002
Posts: 12,133 Likes: 280
|
Joined: Jun 2002
Posts: 12,133 Likes: 280 |
- you know us guys here are used to seeing some magnificent rings/jewelry.
This piece most certainly period shows some excellent workmanship! A lot of work went in to this piece by someone highly skilled.. A work of art,,a campaign, trench etc. made piece I'm sure none of us wouldn't mind owning even if not our specific area/type of ring.. That is a great catch Benten!
|
|
|
|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
Thanks Gaspare, good to see you back ! It is nice to see how the corner in the initial "H" is made ....... a little hole, made by a very small drill , like a needle.
|
|
|
|
Joined: Sep 2000
Posts: 15,094 Likes: 99
|
Joined: Sep 2000
Posts: 15,094 Likes: 99 |
Why the hole ? Any reason ?
Dave
|
|
|
|
Joined: Jan 2018
Posts: 451 Likes: 36
|
Joined: Jan 2018
Posts: 451 Likes: 36 |
Lovely ring, Benten. Good find! Stephen
|
|
|
|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
|
|
|
|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
Why the hole ? Any reason ?
Dave Why the hole ? Any reason ?
Dave Dave, if I remember well.........when you have to saw, on a very little scale like this, you can make a mistake easily and saw too far. If you drill a hole on the end point, before sawing to that point, it is easier to stop there ....specially when two saw lines meet in one point. You have more sawing control. This could be an explanation. Benten
|
|
|
|
Joined: Sep 2000
Posts: 15,094 Likes: 99
|
Joined: Sep 2000
Posts: 15,094 Likes: 99 |
Ahhhh I thought maybe a poison-dispensing ring Dave
|
|
|
|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
Or.... I could use the ring as a salt spreader 😀
Benten
Last edited by benten; 02/23/2021 06:02 PM.
|
1 member likes this:
Stephen |
|
|
|
Joined: Jul 2000
Posts: 5,020 Likes: 31
|
Joined: Jul 2000
Posts: 5,020 Likes: 31 |
Why the hole ? Any reason ?
Dave Why the hole ? Any reason ?
Dave Dave, if I remember well.........when you have to saw, on a very little scale like this, you can make a mistake easily and saw too far. If you drill a hole on the end point, before sawing to that point, it is easier to stop there ....specially when two saw lines meet in one point. You have more sawing control. This could be an explanation. Benten Hello Benten and Dave, the reason for the "hole" is another. The monogram is a separate part, fixed by soldering. As you can see the hole it is in the middle segment of the ring, at the state of manufacturing totally surrounded by the monogram (oposite of the other parts of the monogramm which could be reached from "outside"). Therefore the jeweler had to do this whole to be able to mount the saw blade through this hole in this certain section to cut out the small inner part between "M" and "H". Normally such a hole is done in a way that you cannot detect it after the middle segment is removed, but here the hole was done too near to the monogram itself therefore it can be still detected. Regards,
wotan, gd.c-b#105
"Never look for sqare eggs" as a late owner of an original FHH-dagger used to say.
|
|
|
|
Joined: Sep 2000
Posts: 15,094 Likes: 99
|
Joined: Sep 2000
Posts: 15,094 Likes: 99 |
Thanks, Wotan I learned something new (I still like the poison dispensing theory, myself ) Dave
|
|
|
|
Joined: Jul 2005
Posts: 1,816 Likes: 55
|
OP
Joined: Jul 2005
Posts: 1,816 Likes: 55 |
Hello Wotan and Dave
- You have a good point concerning the middle section; I agree, you have to drill there first, before you can do the saw through the hole and saw the middle section open. I didn’t see that. You are right here Wotan.
-There are also other drill holes that explain my vision: making a drill hole on the end, so you will not saw too far. All is on a very small scale! The maker first made scratch or pencil lines, a design of the initials on the gold plate. Look at the inside corners of the M ; in the corners you can see that the corners are a round ; in the drawing, on the end of the inside vertical lines of the M, the maker has marked a point for the drilling hole, first . The drilling hole was more or less, in the middle of the line, see here -----------------0 ( sawing line and hole) . The saw goes up and meets the drill hole in the middle .The result we see : the inside left line of the M ends a bit more to the left , the right line ends a bit to the right.
For me, both techniques are you used in this ring.
Benten
Last edited by benten; 02/24/2021 07:30 PM.
|
|
|
Forums42
Topics31,668
Posts329,045
Members7,519
|
Most Online5,900 Dec 19th, 2019
|
|
|
|